| 1A
ALGICOAT RC 104 |
Acrylic
Polymer Based Waterproofing System
Properties:
Coating has good breathing capacity
and UV stability. It is suitable for
waterproofing of terraces, bathrooms,
masonry walls, water-tanks, basements
etc.
Application Method:
Mix 1 part of ALGICOAT 104 with 1.8
parts by volume of cement and apply
2 coats by brush on moist and cleaned
surface. Needs 7 days of water curing.
|
| 1B
ALGICOAT ACRYLIC |
Acrylic
based colored/colorless decorative and
protective water proofing coating
Properties: ALGICOAT ACRYLIC is a colored or colorless
waterproofing coating suitable for vertical/sloping
surfaces such as tile/roof, cement painted
and brick surfaces.
Coverages: 40
Sq.ft.for 2 coats
Application Method: Apply 2 coats by brush only on a totally
dry & cleaned surface. The coating will
peel off is applied on wet or moist
surface or during high humidity
|
| 1C
ALGICOAT EPX-W |
Water
Based Epoxy Floor Coating
Properties: Coating is easy to clean and is resistant
to oils, liquid, mild acids and alkalies.
Reduces fungus/algae growth in water
tanks. Available in different colors.
Product can be thinned in water.
Application Method: Mix resin, hardener and water in the
ratio of 1:1:1 by volume to uniform
consistency and apply 2 coats by brush
on moist and cleaned surface.
|
| ID
ALGILATEX |
Latex
polymer additive for polymer modified
concrete/mortar
Application Areas: As grout additive and in mortar for
structural repairs anti-corrosive coating
on reinforcement when mixed with cement.
Application Method: ALGILATEX should be added along with
dosing water to cement grout or cement
mortar.
Dosage: 3.6
Kgs per 50 Kg Cement
|
| 1E
ALGIGROUT ADMIXTURE SP |
Non
Shrink super plasticizing grouting admixture
Application Areas: Suitable as
an admixture for cement grouting in
waterproofing repair to get high flow
& high strength.
Dosage: 225gm
per bag of cement.
Application Method: ALGIGROUT ADMIXTURE SP should be mixed
with cement grout.
|
| IF
ALGIPLUG WELL |
Grout
addictive for plugging honey combs
Application Areas: Provides high penetration and extended
set time & very high water reduction.
Application Method: Mix ALGIPLUG WELL in ratio of 1 Litre
per 50 Kg cement and 50-60 liter water
and grout into the structure.
|
| IG
ALGIFLEX GUARD |
Elastromeric
Waterproofing cum heat insulation system
Properties: Single component, elastomeric, UV stable
and fungus resistant.
Application Method: Mix ALGIFLEX GUARD with water in the
ratio of 1:0:4 ratio and apply 2 coats.
Coverage: About
35 Sq.Ft per Kg for 2 coats.
|
| 1H
ALGICOAT SIL-S |
Water
dilute able solution water repellent
Properties: Reduces fungus/algae formation. Suitable
for exterior of building concrete, natural
stone, online and cement painted surface.
Coverage: Diluted
with water in 1:6 ratio gives 300 to
500 sq.ft per kg on cement coated surface
and 300 to 500 sq.ft per kg on tiles,
bricks etc.
|
| 1I
ALGICOAT SIL-W |
Solvent
silicon based water repellant
Properties: Eliminates fungus or algae formation
and provides water proofing effect.
Does not change the appearance of the
surface. Suitable for exterior of the
building, concrete, natural stone, clay
tile, brick etc.
|
| 1J
ALGIISUEX SP |
A
High Performance Heat Insulation System
Properties:Fungus
Resistant, Reduces Heat temperature
within the building. Reduces or eliminates
air-conditioning cost. The coating is
highly resistant to scrub, abrasion
and UV Light. Suitable for RCC Slabs,
asbestos, metal roofing sheets etc.
Application Method: Clean the surface with wire brush and
wash with water. Apply 2 coats by brush.
Coverage: About 40 Sq.ft per Kg for
double coat.
|
| 15A
ALGICRACK FILLER |
Economical
Cementitious Crack Filler
Properties: Recommended for internal
cracks not subjected to movement. It is non shrink.
Application Method: Clean and
widen the crack, mix ALGICRACK FILLER in 3:1 proportion
& fill up the crack using putty blade.
Coverage: Above 70-80 running
feet per Kg.
|
| 15B
ALGICERACLEAN |
For cleaning,
de-greasing and to remove stain on ceramic and plastic
surface.
Properties: Easily cleans/removes
all kinds of stains, grease, cement, algae, etc., From
ceramic tile and other ceramic and plastic surfaces. Very
mild on skin.
Application Method: Apply over
it to react for 5 minutes and remove it by scrubbing with
plastic brush.
Coverage: About 80-100 Sq.ft per
litre.
|
| 13A
ALGIWOOD GUARD |
Two
component high performance epoxy coating for wood
works.
Properties: High performance
epoxy coating resistant to moisture and chemicals
with high film strength and long service life.
Application Method: Mix
resin hardener and apply 2 coats on dry and clean
wooden surface.
Coverage: 8o Sq.ft per litre
depending on surface absorption.
|
| 6A
ALGIRAPIDCEM |
Ready
to use extra setting (sets within 4 min.) compound
Application: For repairing
cracks in cement pipes, floors, concrete doors,
windows etc., Compressive strength achieved is 150
Kg/cm2 for 2 hour. 300 Kg/cm2 for 1 day, 400 Kg/cm2
for 2 days.
Application Method: Add
A:GIRAPIDCEM to water in the ratio of 5:1 by volume.
Coverage: 0.45 Sq/ft/kg
for 12mm thickness.
|
| 6B
ALGIRAPID PATCH |
Fast
setting cement patching mortar compressive strength
achieved is 2 Hr strength = 150 Kg/cm2, 28 days
strength= 350 Kg/cm2
Properties: ALGIPAD PATCH
sets within half an hour and is suitable for industrial
floor repair, road repairs and any where potholes
are needed tobe repaired very quickly.
Coverage: 2Kg/Sq.Ft/12mm
depth.
Application Method: Clean
the pothole and cut into a rectangle shape groove.
Apply a coat of ALGIBOND LATEX mixed with cement
in 1:0:15 by volume and place this into the prepared
groove. Cure the patch with with water immediately
after set i.e., after 30 minutes cure for 24 hours
before cracking.
|
| 6C
ALGIPLAST RAPIDSET-P |
Extra
Quick Setting Admixture (Sets wihtin 2 min.)
Properties: For sealing
severe water infiltration in case of dams, harbours,
basements, compressive strength is 120 Ks/cm2 for
2 hour and 140 Kg/cm2 for 2 days.
Application Method: Add
ALGIPLAST RAPIDSET to cement in the ratio of 1:3:5
by volume and knead it into a dough and hold it
in the hand until it is warm. Hold this into the
crack till it sets.
Dosage: 26 litre per bag
of cement.
|
| 6D
ALGIRAPIDSET-P |
Set
accelerating powder for dry shortcreting
Application: As an admixture
to impart very fast setting property for dry shortcreting
and granite mixes. Useful for tunnels and for shortcreting
in water proofing repairs.
Application Method: Dry
mix ALGIRAPID-P with cement, sand, jelly. This mix
should be shot using compressor after adding water
only at the last minute.
Dosage: 4.5 Kg(3 to 6 Kg)
per 50 kg bag of cement.
|
| 4A
ALGITILE ADHESIVE |
Tile
Fixing Adhesive
Properties: For fixing ceramic,
marble, mosaic tiles on floor & walls. Suitable
for tile over tile & exterior application.
Coverages: 4.4.5 Sq.ft/Kg.
Application
Method: Mix ALGITILE ADHESIVE with water
in the ratio of 5:2 by volume and spread over clean
surface with notch towel (supplied along), immediately
fix tiles over it.
|
| 4B
ALGITILE AID GP |
The
fixing adhesive for internal application.
Application Areas: For fixing
ceramic, marble, mosaic tile on floors & walls.
Suitable interior application.
Coverages: 4.4.5 sq.ft/Kg.
Application
Method: Mix ALGITILE AID GP with water in
the ratio of 5:2 volume and spread over the clean
surface using a notch trowel (supplied along with
the product) and immediately fix tiles over it.
|
| 4C
ALGITILE JOINT GROUT |
Tile
Joint Grout
Application Areas: Grouting
tile joints in case of ceramic, marble, mosaic etc.
Comes in a wide range of colors.
Application Method: Mix
ALGI TILE JOINT GROUT with water in the ratio of
2:1 by volume & Apply over tile joints.
|
| 4D
ALGITITE |
High
strength 2 component epoxy adhesive
Application Areas: For fixing
granite, plastic, metal, wood etc. Sets within 3
hours. Coverage:25.30 Sq.ft/Kg.
Application Method: Mix
ALGITILE resin and hardener in the ratio of 1:1
by volume. Keep it for 5 minutes and then apply
on clean and dry surface.to be bonded.
|
| 4E
ALGITILE EPX |
Epoxy
based germ free tile joint grout
Application Areas: For grouting
ceramic, marble, mosaic tile joints etc. Stain Resistant
and easy to clean.
Application Method: Tile
joints should be dry. Mix resin & hardener in 1:1
by volume & fill in the joints using putty blade,
suitable for light traffic after 2 days.
Full cure: 7 days. Do not
use for exterior tile joints.
Coverage: 40 Sq.ft for 15cm
tiles.
|
| 11A
ALGIANCHOR CAPSULE |
Expanding
cementatious anchor grout(Normal and Fast Set)
Properties: Expanding type
encapsulated & thixotrophic. Hence ready to use
and saves labour.
Application Method: Dip
ALGIANCHOR CAPSULE in water for 2 to 4 minutes until
it absorbs water and then place it into the pre
drilled bore (hole). Drive reinforcing rod through
the capsule.
|
| 14A
ALGICOAT EPX ZN |
Zinc
rich epoxy primer for metal surfaces.
Properties: Zinc rich epoxy
based anti corrosive primer. Ideal for metal surface
as base coat. Finds its application in industrial
structures, steel gates, irrigation projects etc.,
Application Method: Mix
resin and hardener in the ratio 1:1 by volume &
coat on dry and clean metal surface. It takes 24
hours for curing.
Coverage: 65 Sq.ft per kg
depending on the surface.
|
| 14B
ALGICOAT ANTICORR |
Solvented
epoxy coal tar anti-corrosive coating
Properties: Easy to use.
Highly economical, has good UV stability and coating
is resistant to mild chemicals(PH 5-10) and has
excellent salt water resistance. Suitable as anti-corrosive
coating for radial gates, penstock pipes in dams,
ports, pipe coatings, steel structures. Sewer liners
etc.
Coverage: 55 sq/ft per 2
coats.
Application Method: In the
case of metal surface, Clean the metal surface with
wire brush. Apply a single coat of ALGICOAT EPX
Zn. Wait for 24 hours. The mix ALGICOAT ANTICORR
ZN resin and hardener in the ratio 1:1 by volume
and apply 2 coats. Incase of concrete surface, Clean
the surface apply 2 coats of ALGICOAT ANTICORR 210.
Do not apply ALGICOAT EPX Zn primer on concrete
surface.
|
| 3A
ALGIBOND EPOXY |
Epoxy
based moisture insensitive bonding agent.
Properties:Excellent adhesion
to concrete, screed, mortar etc. For bonding old
to new concrete joints. Coverage: 30 running feet
per Kg.
Application
Method: Mix ALGIBOND EPOXY resin and hardener
and apply single thick coat by brush over clean
and dry surface. Immediately pour fresh concrete
or mortar over it and compact.
|
| 3B
ALGIBOND LATEX |
Latex
Bonding Agent.
Properties: For improving
adhesion between cement mortar & concrete in patch
works repairs, plastering, floor screed concrete
etc.
Coverages: 45 Sq.ft per
liter.
Application Method: Mix
ALGIBOND LATEX with fresh cement in the ratio 1:1:8
by volume and apply one coat by brush over a cleaned
surface. Immediately pour fresh or concrete mortar
over it and compact.
|
| 5A
ALGIPLAST 210N |
Water
Reducing Concrete Plasticizer (Modified Lignosulphate
based)
Application Areas: For
improving strength, durability and for saving
cement of concrete. Suitable for RCC slabs,
beams, columns etc.
Application Method:
Pre dilute with water and then add to wet
concrete mix. Dosage: 75ml to 200ml per 50Kg
bag of cement.
|
| 5B
ALGISUPERBLAST N |
High
range water reducing super plasticizer
Application Areas: For
producing very high early strength concrete
suitable especially for densely packed reinforcement
i.e., for bridges, flyovers etc.
Dosage: 100ml to 750ml
per 50Kg of cement.
|
| 5C
ALGISUPERBLAST R |
High
range water reducing and set retarding super
plasticizer.
Modified napthalene sulphonate condensate
based.
Application: For slump
retention and to produce high strength highly
water reduced pump-able concrete.
Dosage: 100ml to 750ml
per 50Kg of cement.
|
| 5D
ALGIPLAST 210R |
Water
Reducing & Set Retarding Concrete Plasticizer.
Modified Lignosulphate Based.
Application: For slump
retention & retardation of setting time, reduces
cracking of concrete in summer especially
where 43 or 53 grade cement is used. It is
suitable for long distance transportation
of concrete. It is recommended for M15 to
M30 grade concrete.
Application Method: Predilute
with water and then add to wet concrete mix.
Dosage: 100ml to
200ml per 50Kg bag of cement.
|
| 5E
ALGIPLAST AEA |
Air
Entraining Concrete Admixture.
Modified Lignosulphate Based.
Application: An economical
admixture for producing workable and durable
mass concrete for dams, reservoirs, canals,
etc.
Application Method: Add
it to wet concrete mix after prediluting it
water. Dosage: 15-30ml per bag of cement.
|
| 5F
ALGIPLASTERAID |
Mortar
Plasticizer
Properties: Reduces
cracking of mortar, rebound loss and improve
the waterproofing quality.
Method: Predilute
with mixing water & then add to wet cement
mortar mix.
Coverage: 200ml per
50Kg bag of cement.
|
| 2A
ALGISEAL ACRYLIC |
A Single
Component Acrylic Sealant for Roof Cracks
Properties:Single component
ready to use, paintable acrylic sealant. It is suitable
for cracks with movement up to � 10% (expansion
and contraction). Available in plastic containers
and in cartridge.
Coverage: 50 running feat
per Kg.
Application Method: Clean
and widen the cracks to 5mm X 5mm wide section using
a marble cutter and fill it with ALGISEAL ACRYLIC.
After drying fill the crack again. For external
cracks the sealant should be covered with ALGICOAT
RC 104.
|
| 2B
ALGISEAL ACRYLIC GP |
A General
Purpose Crack Filler
Properties: Single Component,
low shrinking and is very suitable for internal
cracks. Movement capacity of �6%
Coverages: 70 running feet
per Kg
Application Method: Clean
and widen the crack to 5mm X 5mm wide section using
a marble cutter. Fill up the sealant once and after
it dries fill up again.
|
| 2C
ALGISEAL PS |
Two
component Polysulphide sealant for expansion joint
& external crack filling. (For Water Proofing Repairs)
Properties: Highly flexible,
UV Light, chemical & Solvent resistant polysulphide
sealant for expansion joint crack filling etc.,
It can be used for joins and cracks with movement
accomodation of �25% (expansion and contraction).
Coverages:
For 12mm wide X 6mm deep 20ft./kg
For 18mm wide X 9mm deep 9ft./kg
For 24mm wide X 12mm deep 9ft./kg
For 25mm wide X 19mm deep 5ft./kg
Application Method: Clean
and dry the joint. Apply ALGISEAL PS primer.Mix
ALGISEAL PS resin & hardener to uniform consistency
& pour into the joint. |
| 9A
ALGICURE |
Emulsified
light reflective wax based curing compound.
Application: Membrane curing
suitable for canal lining, roads, bridges, piers
etc., Especially useful in places of water shortage
and difficult to cure areas such as vertical or
sloping surfaces.
Application Method: To be
applied by spray on fresh(green) concrete plaster
before final set(just after surface water has evaporated).
Coverage: 3.25 sq.meter
per liter for vertical areas and 4 sq.mt per litre
for horizontal areas.
|
| 9B
ALGIFORM COAT C-10 |
Concentrated
& Economical Shutter Release Agent
Application: Dilute 1 litre
with 10 litre diesel to give 11 litre mould release
agent. Very economical easy to store/handle.
Application Method: Dilute
with diesel in the ratio of 1:10 and then apply
on form work by brush/ waste cotton before placing
concrete.
Coverage: 2500 to 4000 Sq.ft
per litre. Depending on the surface.
|
| 12A
ALGIHARD FLOOR NM |
Dry
shake floor hardener and waterproofing suitable
for both dry and wet floors.
Properties: Abrasion resistance
is 3.5 times than that of normal concrete. It produces
high abrasion resistant hard wearing surface, based
on non metallic aggregates that doesnt get corroded.
Ideally suited for chemical plants, wet plants,
diaries, distilleries, etc., Compressive strength
is 600 Kg/cm2.
Coverage: 0.6 Kg per sq.ft.
Application Method: Spread
ALGIHARD FLOOR NM at the rate of 0.4 kg/Sq/ft over
freshly laid concrete floor (2 to 3 hr after placing
concrete) and finish the concrete surface with trowel
or preferable with power trowel. Spread another
0.2 Kg per Sq.ft just before the final set (3 to
4 hours) and finish with trowel or power trowel.
|
| 12B
ALGICOAT EPX 130 |
Light
Duty Epoxy floor Coating (0.2 to 3MM)
Properties: Coating is very
attractive, durable, chemical resistant and is available
in range of attractive colors. Coating is hygenic
and is easily cleanable. It is recommended for food
processing industries, workshops, kitchens, showrooms,
soft drinks, soft drink production and bottling
plants.
Coverage: 2.5 Sq.m.per Kg
of 2 coats.
Application Method: Clean
the concrete/mosaic floor to remove all dirt, wax,
paint etc. And dry totally. Mix resin and hardener
and apply 2 coats by brush within 30 minutes of
mixing. Mix only enough quantity of that can used
in 30 minutes.
|
| 12C
ALGIFLOOR EPX 320 |
Epoxy
Mortar System for Heavy Duty Flooring (3 to 5mm
thickness)
Properties: Excellent impact
and abrasion resistance. Can withstand very heavy
loads. Joint less and non slip suitable for industrial
plants, processing areas, harbors, airports, workshop
flooring subjected to heavy impact loading. Compressive
strength after 2 days = 900 Kg/sq.m.
Application Method: On cleaned
and dried concrete floor apply a ALGICOAT PRIMER.
Wait till is tack free then mix ALGIFLOOR EPX 320
resin and hardener to uniform consistency, then
slowly add filler & mix well. Keep it for 5 minutes.
Place this mortar on floor & finish with trowel.
Coverage: ALGICOAT PRIMER
40 sq.ft/kg.ALGIFLOOR EPX 320=1.1sq.ft/kg for 3mm
|
| 12D
ALGIFLOOR EPX 310 |
Epoxy
Mortar System for Heavy Duty Chemical Resistant
Flooring (3 to 5mm thickness)
Properties: Excellent chemical
resistance. Suitable for flooring subjected to chemical
spillages as well as heavy loading. Suitable for
chemical plants, for processing areas, breweries,
dairies, petrochemical complexes etc., Compressive
strength at 2 days=800 Kg per sq.cm.
Application Method: On cleaned
and dried concrete floor apply a ALGICOAT PRIMER.
Wait till it is tack free then mix ALGIFLOOR EPX
310 resin and hardner to uniform consistency, then
slowly add filler & mix well. Keep it for 5 minutes.
Place this mortar on floor & finish with trowel.
Coverage: ALGICOAT PRIMER:
40 Sq.ft per Kg. ALGIFLOOR EPX 310=1.1 sq.ft for
1 Kg for 3 mm thickness.
|
| 12E
ALGIFLOOR EPX SL |
Solvent
free monolitic seamless self levelling epoxy floor
(3 component system)
Properties: 2-3 mm thick
monolitic seamless, self levelling floor topping
suitable for pharmaceutical units, hospitals, breweries
etc., comes in very attractive colors.
Application Method: Mix
resin, hardener and filler & pour the mix on dry
and cleaned concrete floor. Level the mix with notch
trowel & finish with spike roller. Coverage: 2.65
sq.ft/ 1 Kg of 2 mm thickness.
|
| 10A
ALGIGROUT NS 200 |
Free
flowing non shrink very high strength grout: 28
days.
Compressive strength is 600 Sq.cm
Application: Very high flow
and self compacting and hence doesnt form honey
combs. Increase life of machines due to reduced
vibration and total load transfer. Reduces installation
time to 3 days instead of 28 days. Very high early
and final strength.
Application Method: Mix
with water in the ratio of 0.14 i.e 7 litre/50 Kg
ALGIGROUT NS 200 in a concrete mixer & pour into
the mould and lightly compact.
Coverage: 2.4 Kg grout per
litre volume to be grouted.
|
| 10B
ALGIINJECTION GROUT EPX |
Epoxy
grout is a solvent free, low viscosity injection
liquid based on high strength epoxies.
Application: Highly suitable
for rehabilitation of earthquake/flood/fire damaged
structures.
Application Method: Resin
and hardener mixed to uniform consistency & is injected
into cracks under pressure.
Coverage: 1.8 Kg grout per
litre of volume to be grouted.
|
| 10C
ALGIGROUT EPX |
High
strength free flow epoxy grout
Application: 3 days compressive
strength is 900 Kg/cm2 suitable for crane, drop
forgers and heavy dynamic loads etc.,
Application Method: Mix
ALGIGROUT EPX resin, hardener to uniform consistency
and then add quartz and mix to uniform color. Pour
this in the foundation.
Coverage: 1.25 Kg per litre
volume to be grouted.
|
| 10D
ALGIGROUT PE |
High
strength polyester free flow grout.
Application: Mechanical
and chemical properties of very high order are obtained
within few hours and is suitable for anchoring,
quick repairs etc.,
Application Method: Mix
resin, hardener & quartz and pour. Sets within few
minutes.
Coverage: 1.8 Kg/litre volume.
|
| 10E
ALGIGROUT ADMIXTURE |
Application: Plasticizing non shrink grouting admixture. Suitable
in making non shrink concrete grout at site.
Properties: Positive expansion
ensures 100% contact with the surface. Suitable
in making non shrink concrete grout at site.
|
| 7A
ALGIPLAST HB |
Gives
a very Good Finish
Application Method: Add
it to wet concrete mix after pre-diluting it with
water.
Dosage: 200 ml per 50 Kg
bag of cement.
|
| 7B
ALGIPLAST HB-B |
Gives
a Higher Strength
Application Method: Add
it to wet concrete mix after pre-diluting with water.
Dosage:200 ml per 50 Kg
bag of cement
|
| 7C
ALGIPLAST HB-200 |
Gives
very high strength & Good Finish
Application Method: Add
it to wet concrete mix after pre-diluting with water.
Dosage: 150ml per 50 Kg
of cement.
|
| 8A
ALGIPLAST MTA |
Colorless
Accelerator for Mosaic Tiles
Application: For high early
compressive strength, earlier shifting of tiles,
to reduce curing time and breakages.
Application Method: Add
it to wet concrete mix after pre-diluting it with
water.
Dosage: 250 to 500 ml per
50 Kg bag of cement.
|
